| Description | The Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, asThe Cable Detector is a portable testing device for diagnosing faults in network and coaxial cables and is used for the rapid inspection of structured cabling. The Cable Detector supports shielded and unshielded twisted-pair cables of categories Cat 3, Cat 5, Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A, as well as coaxial cables, such as those used in TV, antenna, and surveillance systems.
Testing is carried out using a two-part system consisting of a main unit and a remote unit, which also allows permanently installed cables to be tested reliably. The most important test procedures include continuity testing of the conductors (pins 1–8), wiring testing to check the correct assignment of the wire pairs, and the detection of short circuits, wiring faults, and split-pair faults. In addition, the shielding of shielded cables is checked. The test range covers cable lengths of up to 305 m, whilst the minimum cable length for split-pair detection is approximately 0.5 m.
Our Cable Detector operates using test signals transmitted between the main unit and the remote unit. The results are displayed via LED indicators. Steady LEDs indicate correct wiring, whilst flashing LEDs indicate faults in the respective wire pairs. Additional status LEDs indicate the type of fault, such as short circuit, miswiring, reversal, or split pair.
The Cable Detector is used in network technology, building cabling, and in IT and communications installations, and is designed for electricians, network technicians, and service technicians to quickly test cable runs.... Read More | The Environmental Meter is a versatile multiple gas detector for simultaneous monitoring of up to four gases, including combustible gases (Ex), oxygen (O?), carbon monoxide (CO) and hydrogen sulfide (H?S). Thanks to modern electrochemical and catalytic sensors, the Environmental Meter ensures high The Environmental Meter is a versatile multiple gas detector for simultaneous monitoring of up to four gases, including combustible gases (Ex), oxygen (O?), carbon monoxide (CO) and hydrogen sulfide (H?S). Thanks to modern electrochemical and catalytic sensors, the Environmental Meter ensures high measurement accuracy of ? ±5% of the final value and delivers reliable results even under demanding environmental conditions. The Environmental Meter has an easy-to-read LCD display with backlighting that clearly shows real-time measurements, system status, date, time and battery level. If the preset alarm limits are exceeded, the device immediately warns the user with visual, audible and vibration alarms. The alarm parameters – including low and high thresholds as well as STEL and TWA limits – can be individually adjusted to meet specific operational requirements and legal specifications.
In addition to classic measurement mode, the Environmental Meter offers extensive additional functions such as self-test, zero and multi-point calibration, and an internal memory for alarm and measurement events. This also makes it suitable for documenting occupational safety measures and for test reports. The intuitive menu navigation via an ergonomic keypad allows for easy operation even when wearing protective gloves.
The integrated Li-ion battery provides up to 8 hours of operation and can be quickly recharged. The robust housing made of impact-resistant plastic with non-slip rubber coating is dustproof and waterproof in accordance with IP66 and designed for harsh industrial environments. In addition, the Environmental Meter meets the requirements of explosion protection class Ex ib IIB T3 Gb and is therefore suitable for use in potentially explosive atmospheres.
Thanks to its compact design and low weight, the Environmental Meter can be conveniently worn on a belt or work clothing. It is ideal for mobile use during maintenance work, in confined spaces (e.g. containers or shafts), during inspection rounds and in emergency and rescue operations.
Typical areas of application for the Environmental Meter include industry, mining, sewage treatment plants, energy suppliers, chemical and petrochemical production, waste management, utility companies, fire brigades and technical emergency services. Wherever hazardous or explosive gas atmospheres may occur, the Environmental Meter offers reliable protection for employees and equipment and contributes significantly to compliance with occupational health and safety regulations.... Read More | The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be operated in both clockwise and anti-clockwise directions.
The Material Tester supports several operating modes, such as Peak Hold, MAX, and real-time measurement. In Peak Hold mode, the maximum value is automatically stored, and the measurement data can be transferred via USB to the software, which also enables a pass/fail evaluation. Tolerance ranges can be set directly on the device, allowing values to be checked quickly. An integrated LED traffic light display shows the measured value at a glance.
The choice between the units Newton-meter (N·m), kilogram-force-centimeter (kgf·cm), and pound-force-inch (lbf·in) enables flexible applications across various industries. With a storage capacity of 2,000 measurement groups and the option of data transfer via USB, the measuring instrument is ideal for use in the mechanical engineering industry and in scientific research facilities.
The Material Tester operates reliably at ambient temperatures of 5 °C to 40 °C and is powered by a 7.2 V NiMH battery, which is optimized for mobile use.... Read More | The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be The Material Tester is a high-quality measuring instrument designed for calibrating torque sensors and for the precise measurement of the tightening torque of screws and other fasteners. The Material Tester offers a high accuracy of ±1% within the range of 10% ... 100% of the scale and can be operated in both clockwise and anti-clockwise directions.
The Material Tester supports several operating modes such as Peak Hold, MAX, and real-time measurement. In Peak Hold mode, the maximum value is automatically stored, and the measurement data can be transferred via USB to the software, which also enables a pass/fail evaluation. Tolerance ranges can be set directly on the device, allowing values to be checked quickly. An integrated LED traffic light display shows the measured value at a glance.
The choice between the units Newton-meter (N·m), kilogram-force-centimeter (kgf·cm), and pound-force-inch (lbf·in) enables flexible applications across various industries. With a storage capacity of 2,000 measurement groups and the option of data transfer via USB, the measuring instrument is ideal for use in the mechanical engineering industry and in scientific research facilities.
The Material Tester operates reliably at ambient temperatures of 5 to 40°C / 41 … 104°F and is powered by a 7.2V NiMH battery, which is optimized for mobile use.... Read More | UV Meter / UV Tester / Internal sensor / Hold function / Battery operation / Compact and lightweight / Automatic switch-off
The UV Meter / UV Tester is a compact measuring device for detecting UV-A radiation in the range of 300 ... 390 nm, with a peak wavelength of 365 nm. The UV Meter / UV Tester UV Meter / UV Tester / Internal sensor / Hold function / Battery operation / Compact and lightweight / Automatic switch-off
The UV Meter / UV Tester is a compact measuring device for detecting UV-A radiation in the range of 300 ... 390 nm, with a peak wavelength of 365 nm. The UV Meter / UV Tester measures radiation intensities from 0 ... 19,999 µW/cm2 with a resolution of 1 µW/cm2 and an accuracy of ± 4% FS. The measuring rate is one measurement per second, a hold function enables the current value to be recorded.
The UV Meter / UV Tester has an integrated sensor, an easy-to-read 1.4-inch LED display, a battery indicator and automatic switch-off after 4 minutes to save energy. It is powered by two 1.5V AA batteries, which makes mobile use particularly convenient.
The UV Meter / UV Tester is ideal for applications such as UV curing in industry, UV controls in medicine, occupational safety measurements and laboratory and environmental technology. The combination of integrated sensor, high accuracy and user-friendly design makes it a reliable tool for a wide range of professional requirements.... Read More |