| Description | Safeguarding sensitive electronic components in manufacturing and handling environments requires precise measurement technology. The Electrical Tester is the indispensable, portable instrument for quickly and reliably checking the surface resistance of materials in ESD-controlled areas.
The Safeguarding sensitive electronic components in manufacturing and handling environments requires precise measurement technology. The Electrical Tester is the indispensable, portable instrument for quickly and reliably checking the surface resistance of materials in ESD-controlled areas.
The Electrical Tester is battery-operated and has integrated parallel electrodes that enable direct testing of the material surface resistance. Thanks to the automatic test voltage selector, the surface resistance tester guarantees maximum measurement accuracy across all relevant ranges. The test voltage automatically switches from 10 V to 100 V as soon as the measured resistance exceeds the value of 1 × 10? ohms.
Two banana sockets allow the connection of external electrodes weighing around 2.25 kg. With these additional components, the Electrical Tester is able to perform professional compliance measurements, such as resistance point-to-point (RTT) or resistance to ground (RTG). The measurement data obtained with this Electrical Tester is essential to ensure adherence to a compliance verification plan (ANSI/ESD S20.20-2007).
The Electrical Tester is ideal for use in electronics production, for testing ESD work mats, workbenches and floor coverings or even in laboratory environments and for quality assurance.... Read More | The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating and direct current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, The Clamp Meter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating and direct current that can be measured without direct contact to the line. The Clamp Meter is suitable for measuring resistance, temperature, diodes, continuity, frequencies and capacitance and is particularly useful for diagnosing electrical and electronic components.
For maximum measurement accuracy, the Clamp Meter supports True RMS for non-sinusoidal waveforms and a Low Impedance (LoZ) function to reduce interference. The non-contact voltage test enables reliable detection of voltages in cables and sockets.
The 2-inch LC display ensures clear readability, even under poor lighting conditions and an integrated LED torch makes it easier to work in dark environments. The device also offers automatic and manual measurement range selection, allowing it to be flexibly adapted to different measuring situations. The device also has a practical zero key which enables accurate measurement of low currents, especially when measuring direct current (DC) and ensures the compensation of deviations of the output value. Other functions include overload protection, data hold, min, max and an automatic power-off after 15 minutes to conserve battery life. The power-off can also be deactivated for longer measurements.
Compact and easy to use, the Clamp Meter is ideal for electrical installations, maintenance work and use in automation technology. It enables safe and efficient measurements, often without direct intervention in the circuit.... Read More | Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the Gas Detector / Gas Detection Instrument / Detects natural gas & LPG / Heat and gas sensor / WLAN / Voice announcement / Control via app / Real-time alarm / Easy installation
A Gas Detector / Gas Detection Instrument is an important safety device. It recognizes dangerous gas concentrations in the air and sounds the alarm in good time to prevent accidents such as explosions or poisoning. Our Gas Detector / Gas Detection Instrument has been specially developed for use in homes, offices and similar indoor areas. It detects both natural gas (methane) and liquefied petroleum gas (LPG, consisting of propane and butane) and reacts as soon as a certain concentration is exceeded.
Our Gas Detector / Gas Detection Instrument measures gas concentrations in the range of 0 ... 100% of the lower explosion limit (LEL), whereby the alarm is triggered at 6% LEL. The response time is a maximum of 30 seconds and the alarm is triggered at a volume of over 70 decibels. A heat sensor is also integrated, which also triggers an alarm at an ambient temperature of 57°C / 134.6°F.
The detector is equipped with a color LCD display that shows the date and time as well as the gas values, the temperature and the remaining sensor life. A Wi-Fi connection is used to connect to the "Smart Life" app, which can be used to monitor the status of the device worldwide. In the event of an alarm, an acoustic and visual warning, a voice message and a push notification are sent to the smartphone. In addition, a connected valve can be activated automatically to stop the gas supply. The sensor has a service life of five years and the device requires a warm-up time of 180 seconds after switching on. The detector is supplied with 5V/1 A power via micro USB and consumes less than 200 mA.
The installation of the Gas Detector / Gas Detection Instrument depends on the type of gas used: for natural gas, which is lighter than air, the device is installed about 30 cm below the ceiling, for LPG, which is heavier than air, about 30 cm above the floor. The distance to the gas source should be 1.5 to 4 meters / 5 to 13 ft. The Gas Detector / Gas Detection Instrument can be attached either with screws or double-sided adhesive tape. Regular tests, which can also be carried out via the app or manually on the device, ensure that it is working properly.
Overall, the Gas Detector / Gas Detection Instrument offers a modern and reliable solution for the early detection of gas leaks and thus makes a significant contribution to increasing safety in rooms supplied with gas. This model of Gas Detector / Gas Detection Instrument combines modern technology with simple operation and is ideal for private and commercial applications.... Read More | Our robust socket square inserts are specially designed for use with impact wrenches and are ideal for demanding bolting applications. The range covers thread sizes from M16 to M48 and offers the right wrench sizes for a wide variety of applications.
These high-quality socket square inserts impress Our robust socket square inserts are specially designed for use with impact wrenches and are ideal for demanding bolting applications. The range covers thread sizes from M16 to M48 and offers the right wrench sizes for a wide variety of applications.
These high-quality socket square inserts impress with their high load-bearing capacity, precise fit, and long service life – perfect for professional use in industry and assembly.... Read More | UV Meter / UV Tester / External sensor / Hold function / Battery operation / Compact and lightweight / Automatic switch-off
The UV Meter / UV Tester is a compact measuring device for detecting UV-A radiation in the range of 300 ... 390 nm, with a peak wavelength of 365 nm. The UV Meter / UV Tester UV Meter / UV Tester / External sensor / Hold function / Battery operation / Compact and lightweight / Automatic switch-off
The UV Meter / UV Tester is a compact measuring device for detecting UV-A radiation in the range of 300 ... 390 nm, with a peak wavelength of 365 nm. The UV Meter / UV Tester measures radiation intensities from 0 ... 19,999 µW/cm2 with a resolution of 1 µW/cm2 and an accuracy of ± 4% FS. The measuring rate is one measurement per second, a hold function enables the current value to be recorded.
The UV Meter / UV Tester has an easy-to-read 1.4-inch LED display, a battery indicator and automatic switch-off after 4 minutes. The external sensor measures 78 × 38.5 × 15.5 mm and is connected via a 1 m cable - ideal for flexible applications. It is powered by two 1.5V AA batteries.
The UV Meter / UV Tester is suitable for numerous applications such as UV curing in industry, UV controls in medicine, occupational safety measurements and for laboratory and environmental technology. Thanks to the accuracy of the UVA radiation meter and its ease of use, the UV Meter / UV Tester is a reliable tool for many professional applications.... Read More |